Ultimate MagSafe Charging Kit Shelf

Works perfectly!!

This was well designed and fit perfectly in my launch addition Rivian R1T and when you add the QC charging pucks you can get on this site work and looks nice

At a minimum it would be nice to get some kind of instructions.
I know what I was doing, but still had to be sure and use outside equipment to install correctly.

Works as promised

Easy install. The hardest part was disconnecting the wires from the vehicle. A little stubborn. Other than that, all working as promised. Fits snug, looks like it is OEM. Better than before. Charges great. 5 star.

Works great, super easy install

Works great, super easy install

Works great, super easy install

Works great, super easy install

Great 3d print that fits and works well. Couldn't be happier with the end result.

Great kit to make the useless Rivian charging system actually work. USB-A and the strange DC barrel connecter are sub-optimal, but overall works as expected.

Your video was perfect in putting together the kit. Works like a charm. Very nice to get wireless charging

Kit fit very well was easy to install and holds the phone without it moving
Under fairly severe conditions
Very good upgrade

This is nice addition to the whole charger replacement that comes with RIVIAN’s . With the addition of the solid bottom on main part this is easy to install and easy to remove to clean

This is an awesome design easy to plug in fits perfectly on my Launch addition Rivian R1T

I was satisfied with the original charging pad when I had an iPhone SE, but after I upgraded to a iPhone 16, the original pad wouldn't charge two phones side-by-side. I found this pad after searching for solutions and I like it because it replaces the original pad rather than sits on top of it. Very satisfied!

Great Design and built quality

This is an excellent functional design. The connection design needs help. However unless you solder, expect to invest time in tinkering to ensure a stable power connection. Soldering requires two welds in about 1/4” of space. A few ideas for OpenSource. A) Design a pre assembled / soldered version. B) design a push to connect connector. C) Design a simple pin that can be connected to barrel connector with a heat gun solder joint and directly insert into the Rivian connector.

I have a 3D printer and even bought the USB adapter from Amazon - (TFTL!). It took me two prints and it got "ok" but my printer isn't large enough. So I'm returning the Amazon USB and ordering all through you (print included). Thanks for being open source an keep being awesome!

I went the solder route and it was great, except that the 12v barrel connector was not connected well to the board. This caused an intermittent loss of power. Added a small plastic shim to the case after adding a dab of solder and we are up and running.

Great fit. Works perfect.

This is an awesome magnetic wireless charging pad. It works great.

I have to agree with the other reviews that this install is a tight fit, and you definitely need to plan to route the DC connector into the little hole in the back of the console. I went with the screw in wiring, and found the pre-stripped/tinned leads were too short to bottom into the connector. Since there is a LOT of slack in that cable, opted to cut and strip new leads that were a touch bit longer. Helpful to have some electrical tape to clean up the work/wiring and some small pieces of double back mounting foam to hold both the power block and OEM power connector in place during final install.

Overall a good solution to keep the USB-C ports open in the center console. One star taken off as the install was a bit more finicky than was expected.

I ordered the Magesafe pads with power kit. I soldered the leads vs. using the screws--it was simple and straight forward. I like having the center console ports available and this power kit keep the install clean (no visible cables). The one trick is to look at the photo on this website and note the power cable to the USB block tucks into an existing cutout. This leave a little more room for the other cables. I also added a small amount of stickyback 1/8 foam to make sure nothing rattles.

This kit enabled a clean install and is a very functional addition to my (much loved) R1T!

Would have been much easier to install if the DC plug was a right angle.

The JSAUX Qi adapters get quite hot even with this open design. Time will tell how will it functions, especially on a long summer roadtrip.