{"product_id":"triplelock-phone-mount-for-r2","title":"TripleLock Phone Mount for R2","description":"\u003ch2\u003eTripleLock Phone Mount for the Rivian R2\u003c\/h2\u003e\n\u003cp\u003eThe OpenSourceEV Parts \u003cstrong\u003eTripleLock Phone Mount\u003c\/strong\u003e puts your phone right where you want it in the Rivian R2: at eye level, clear of the steering wheel, and within easy reach. It locks in solid, so your screen stays steady instead of bouncing on every bump, and it leaves the dash vent working exactly as it should.\u003c\/p\u003e\n\u003cp\u003eDesigned, manufactured, and supported by OpenSourceEV, and \u003cem\u003eextensively\u003c\/em\u003e tested in a Rivian R2.\u003c\/p\u003e\n\u003ch3\u003eWhy the TripleLock\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eThe Right Spot:\u003c\/strong\u003e The TripleLock sits at the far left end of the dashboard, next to the driver's door -- the only place with room. Your phone stays in your line of sight for navigation and calls without blocking the R2's screens or hiding behind the steering wheel.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLocked In, Not Just Clipped On:\u003c\/strong\u003e Most snap-in phone mounts are held only at the top and bottom, which lets them pivot and bounce over every bump. The TripleLock is held at three points -- the left, the bottom, and a diagonal from the top to the right -- so it has nowhere to move. Your phone stays steady and stays where you aimed it.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eYour Air Vent Still Works:\u003c\/strong\u003e The left end of the R2's dash vent has a short section with no airflow. The TripleLock fits entirely inside that section, so the vent keeps blowing exactly as Rivian designed it.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNo Damage, No Modifications:\u003c\/strong\u003e It snaps in by hand behind the existing dash trim in less than 5 seconds. No adhesives, no drilling, no tools in the car, and it pops back out cleanly whenever you want.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWorks With the Holder You Want:\u003c\/strong\u003e The mount uses a standard ball joint, the same connection most car phone holders use. Add one of our MagSafe holders at checkout, or use a compatible holder you already own.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBuilt to Last:\u003c\/strong\u003e The ball is bolted on with a stainless steel bolt and nut, not plastic clips that can snap. If you ever switch holders or damage the ball, you replace just the ball -- not the whole mount.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMade for Car Interiors:\u003c\/strong\u003e This is a 3D printed part made from ASA, a plastic designed to resist sun fading and heat, so it holds up on a dashboard year-round. We print every one ourselves in Pittsburgh, PA, and back it with a 1-year warranty.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePassenger Side Available:\u003c\/strong\u003e A mirror-image passenger-side version is sold separately.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy Three Points Matter\u003c\/h3\u003e\n\u003cp\u003eA phone mount is only as good as what it's anchored to. A mount held at just two points acts like a hinge: the weight of your phone rocks it back and forth, and road vibration does the rest. Your screen shakes, the holder works loose, and your phone ends up pointed somewhere you didn't aim it. The TripleLock's third, diagonal contact point removes that hinge. Once it snaps in, it stays put -- on the highway and on rough pavement.\u003c\/p\u003e\n\u003ch3\u003eChoosing a Phone Holder\u003c\/h3\u003e\n\u003cp\u003eThe TripleLock is the part that attaches to your R2. The phone holder is the part that holds your phone. It clamps onto the round ball at the end of the mount, and you can tilt and rotate it to the exact angle you want, then lock it with a small screw on the back.\u003c\/p\u003e\n\u003cp\u003eWe've standardized on MagSafe so your phone snaps on and off magnetically with one hand. MagSafe is built into iPhone 12 and newer, and MagSafe-compatible cases are available for nearly every phone on the market, Android included. If your phone or case doesn't have MagSafe, every holder includes a metal ring you can stick to your phone or case so it works the same way.\u003c\/p\u003e\n\u003cp\u003eFour holders are available at checkout, with more coming soon:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOSEV Offset Charging MagSafe:\u003c\/strong\u003e Our own holder. Charges your phone wirelessly while it's mounted. A dim blue LED ring helps you line up your phone at night. Draws less than 1mW when not charging, so it won't drain your battery. 17mm only.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eATB 720 Degree MagSafe:\u003c\/strong\u003e Non-charging. A second adjustment point along the arm gives the most positioning flexibility of any holder we carry.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLisen Offset MagSafe:\u003c\/strong\u003e Non-charging. A simple, slim magnetic holder with an offset arm.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLisen Charging MagSafe:\u003c\/strong\u003e Charges your phone wirelessly, fast and with minimal heat. A near-invisible blue LED ring helps you line up your phone at night. Draws less than 1mW when not charging.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eCharging holders include a USB-A to USB-C cable and need an OBD-II to USB power source to plug into -- more on that below.\u003c\/p\u003e\n\u003ch3\u003eBall Size Guide\u003c\/h3\u003e\n\u003cp\u003ePhone holders are made to fit a few common ball sizes, so the ball on your mount needs to match your holder. The TripleLock is available with a 17mm, 20mm, or 1-inch ball, or a combo pack with all three. The 17mm size fits the vast majority of phone holders, including every holder we sell. The 20mm size fits Offroam x Peak Design co-branded holders. The 1-inch size is for RAM-branded accessories only. If you're buying a holder from us or aren't sure, choose 17mm or the combo pack.\u003c\/p\u003e\n\u003ch3\u003eCharging Your Phone\u003c\/h3\u003e\n\u003cp\u003eA charging holder needs a power source. The recommended option is the OpenSourceEV OBD-II adapter, which plugs into your R2's OBD-II port (a standard connector found on every modern car) and provides both a USB-A Quick Charge 3.0 port and a USB-C PD port, with up to 48W of total combined output. That's enough to charge your phone at 15W.\u003c\/p\u003e\n\u003cp\u003eFaster 25W wireless charging requires a 15-volt USB-C PD supply, and we tested five OBD-II to USB adapters -- including every one our competitors sell -- and none of them provide it. If someone claims faster charging from an OBD-II port, be very, \u003cem\u003every\u003c\/em\u003e skeptical.\u003c\/p\u003e","brand":"OpenSourceEV","offers":[{"title":"17MM \/ Mount Only","offer_id":52984591253784,"sku":"3Lock_17","price":14.95,"currency_code":"USD","in_stock":true},{"title":"17MM \/ ATB 720 Degree Magsafe","offer_id":52984591286552,"sku":null,"price":22.95,"currency_code":"USD","in_stock":true},{"title":"17MM \/ Lisen Magsafe Offset","offer_id":52984591352088,"sku":null,"price":23.95,"currency_code":"USD","in_stock":true},{"title":"17MM \/ Lisen Magsafe Charging","offer_id":52984591384856,"sku":null,"price":29.95,"currency_code":"USD","in_stock":true},{"title":"17MM \/ OSEV Offset Magsafe Charging","offer_id":52984591319320,"sku":null,"price":27.95,"currency_code":"USD","in_stock":true},{"title":"20MM \/ Mount Only","offer_id":52984591450392,"sku":"3Lock_20","price":14.95,"currency_code":"USD","in_stock":true},{"title":"1 Inch \/ Mount Only","offer_id":52984591483160,"sku":"3Lock_1IN","price":14.95,"currency_code":"USD","in_stock":true},{"title":"All \/ Mount Only","offer_id":52984906383640,"sku":null,"price":15.95,"currency_code":"USD","in_stock":true},{"title":"All \/ ATB 720 Degree Magsafe","offer_id":52984906416408,"sku":null,"price":23.95,"currency_code":"USD","in_stock":true},{"title":"All \/ Lisen Magsafe Offset","offer_id":52984906449176,"sku":null,"price":24.95,"currency_code":"USD","in_stock":true},{"title":"All \/ Lisen Magsafe Charging","offer_id":52984906481944,"sku":null,"price":30.95,"currency_code":"USD","in_stock":true},{"title":"All \/ OSEV Offset Magsafe Charging","offer_id":52984906514712,"sku":null,"price":28.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0550\/9975\/2605\/files\/BDE85B41-359A-47A5-B7C9-9BFEF843640F_1_201_a.jpg?v=1792694000","url":"https:\/\/opensourceev.com\/products\/triplelock-phone-mount-for-r2","provider":"OpenSource EV Parts","version":"1.0","type":"link"}